{"id":1422,"date":"2026-09-04T14:09:42","date_gmt":"2026-09-04T06:09:42","guid":{"rendered":"https:\/\/sheeonpulp.com\/?post_type=news&p=1422"},"modified":"2026-09-02T14:21:20","modified_gmt":"2026-09-02T06:21:20","slug":"bleached-bamboo-pulp-specs-for-tissue-and-print-paper","status":"publish","type":"news","link":"https:\/\/sheeonpulp.com\/vi\/tin-tuc\/bleached-bamboo-pulp-specs-for-tissue-and-print-paper\/","title":{"rendered":"Bleached Bamboo Pulp: Specs for Tissue and Print Paper"},"content":{"rendered":"

Sheeon Pulp Technical Team | Published 2026-09<\/p>\n

B\u1ed9t tre t\u1ea9y tr\u1eafng<\/a><\/strong><\/span> runs approximately 85% brightness with viscosity in the 600\u2013800 ml\/g range, and those two numbers alone don’t tell you whether a lot will run cleanly on a tissue or printing line. This spec sheet breaks down every published parameter and what it actually predicts for each application.<\/p>\n

Full Specification Table<\/h2>\n\n\n\n\n\n\n\n\n\n\n\n\n
Tham s\u1ed1<\/b><\/strong><\/td>\nPublished Value<\/b><\/strong><\/td>\nPh\u01b0\u01a1ng ph\u00e1p th\u1eed nghi\u1ec7m<\/b><\/strong><\/td>\n<\/tr>\n
\u0110\u1ed9 s\u00e1ng<\/td>\n~85%<\/td>\nGB\/T 7982<\/td>\n<\/tr>\n
Dirt count, 0.3\u20131.0 mm\u00b2<\/td>\n<25 mm\u00b2\/500 g<\/td>\nGB\/T 1548<\/td>\n<\/tr>\n
Dirt count, 1.0\u20134.0 mm\u00b2<\/td>\n<20 mm\u00b2\/500 g<\/td>\nGB\/T 1548<\/td>\n<\/tr>\n
Dirt count, >4.0 mm\u00b2<\/td>\nKh\u00f4ng c\u00f3<\/td>\nGB\/T 1548<\/td>\n<\/tr>\n
Ch\u1ec9 s\u1ed1 \u0111\u1ed9 b\u1ec1n k\u00e9o<\/td>\n>55 N\u00b7m\/g<\/td>\nGB\/T 8940.2<\/td>\n<\/tr>\n
Ch\u1ec9 s\u1ed1 \u0111\u1ed9 r\u00e1ch<\/td>\n>8.5 mN\u00b7m\u00b2\/g<\/td>\nGB\/T 10740<\/td>\n<\/tr>\n
Ch\u1ec9 s\u1ed1 b\u00f9ng n\u1ed5<\/td>\n>5.0 kPa\u00b7m\u00b2\/g<\/td>\nGB\/T 10336-2002<\/td>\n<\/tr>\n
\u0110\u1ed9 nh\u1edbt<\/td>\n600\u2013800 ml\/g<\/td>\nNot separately specified on product page<\/td>\n<\/tr>\n
Fiber length<\/td>\n>1.7 mm<\/td>\nNot separately specified on product page<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

These are the parameters published on Sheeon’s product page. Test method mapping above follows how each method is generally used against the associated parameter \u2014 buyers specifying against this table should request the actual test report tied to the delivered lot, since a published range describes the product line, not any individual shipment.<\/p>\n

What Each Parameter Actually Predicts<\/h2>\n

Brightness: the number buyers over-index on<\/strong><\/p>\n

At ~85%, b\u1ed9t tre t\u1ea9y tr\u1eafng<\/a><\/strong><\/span> sits below premium bleached wood pulp grades that often clear 88\u201390%, but well above b\u1ed9t gi\u1ea5y tre ch\u01b0a t\u1ea9y tr\u1eafng<\/a><\/strong><\/span>‘s 40\u201343%. For tissue converters, brightness is mostly a visual and brand-perception spec \u2014 it doesn’t predict softness or absorbency on its own. For printing paper, brightness affects contrast and how ink colors read on the finished sheet, which matters more for coated or premium uncoated grades than for basic commercial printing stock.<\/p>\n

\"B\u1ed9t<\/p>\n

Dirt count: the spec that actually causes line stoppages<\/strong><\/p>\n

Dirt count is broken into two size bands \u2014 fine specks (0.3\u20131.0 mm\u00b2) and larger particles (1.0\u20134.0 mm\u00b2) \u2014 with zero tolerance above 4.0 mm\u00b2. This is the parameter most likely to cause real production problems if a lot runs outside spec: visible specks in tissue show up immediately to end consumers, and larger dirt particles can catch on calender rolls or cause web breaks on high-speed printing presses. A brightness reading can look fine while dirt count quietly runs high \u2014 they’re independent measurements, and buyers who only check brightness on incoming lots are missing the parameter more likely to cause a stoppage.<\/p>\n

Viscosity: the proxy for pulp degradation<\/strong><\/p>\n

The 600\u2013800 ml\/g range reflects how much the cellulose chain length has been preserved through pulping and bleaching \u2014 lower viscosity generally means more chain degradation, which translates to lower strength potential even if tensile and burst numbers on that specific lot still test within range. Viscosity matters most to mills running their own refining process, since a pulp already low in the range gives less room to refine before strength drops off. This spec isn’t cosmetic; it’s closer to a leading indicator than tensile or burst index, which are downstream results.<\/p>\n

Tensile, tear and burst index: the runnability specs<\/strong><\/p>\n

Tensile index (>55 N\u00b7m\/g), tear index (>8.5 mN\u00b7m\u00b2\/g) and burst index (>5.0 kPa\u00b7m\u00b2\/g) together describe how the sheet holds together under mechanical stress \u2014 pulling, tearing and localized pressure respectively. For printing paper running on high-speed presses, tensile index is the one most directly tied to web breaks. For tissue, these numbers matter less in absolute terms and more in how they trade off against softness, since higher-strength furnish often runs firmer than converters want for a premium tissue feel.<\/p>\n

\"B\u1ed9t<\/p>\n

Tissue vs. Printing Paper: Which Specs to Weight<\/h2>\n\n\n\n\n\n\n
Priority<\/b><\/strong><\/td>\nTissue Manufacturers<\/b><\/strong><\/td>\nPrinting Paper Manufacturers<\/b><\/strong><\/td>\n<\/tr>\n
1st<\/td>\nDirt count (visible in thin sheet)<\/td>\nTensile index (press runnability)<\/td>\n<\/tr>\n
2nd<\/td>\nBrightness (perceived quality)<\/td>\nBrightness (print contrast)<\/td>\n<\/tr>\n
3rd<\/td>\nViscosity (softness\/strength balance)<\/td>\nBurst and tear index<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Tissue lines generally want the fine dirt-count band as clean as possible and can tolerate strength indices at the lower end of the published range, since excess strength works against softness. Printing lines lean the opposite way \u2014 tensile index close to or above the published minimum matters more than shaving another point off dirt count, particularly on uncoated commercial print stock where dirt tolerance is naturally a bit more forgiving than tissue.<\/p>\n

The Misconception: “Higher Viscosity Always Means Better Pulp”<\/h2>\n

Not necessarily. Viscosity indicates less fiber degradation, which is generally desirable, but a mill running its own bleaching or refining downstream may specifically want pulp mid-range in viscosity rather than at the top, since very high viscosity can mean more energy required in refining to hit target freeness. Buyers should specify viscosity against their own process requirements rather than assuming the top of the published range is automatically the better lot.<\/p>\n

Certification Status for This Grade<\/h2>\n

Bleached bamboo pulp is one of the few grades in Sheeon’s catalog where FSC appears as a listed claim, alongside CE and SGS, with FDA-related food-contact language also referenced on the product page. None of these come with a published certificate number. For FSC specifically, checking the certificate holder name, code and scope in the Forest Stewardship Council’s public certificate database before finalizing a spec sheet that references FSC status is the only way to confirm the claim independently \u2014 a website statement isn’t equivalent to a checked certificate.<\/p>\n

Trade-offs to Weigh Before Specifying This Grade<\/h2>\n

B\u1ed9t tre t\u1ea9y tr\u1eafng<\/a><\/strong><\/span>‘s tear and burst index hold up well relative to its brightness class, and the fiber source gives buyers a genuine alternative-fiber story distinct from wood pulp. Set against that: viscosity and fiber length aren’t tied to a specific test method on the published product page, which means buyers who need those figures for process-control documentation should request them directly rather than assuming a standard method applies. Brightness at ~85% also sits below top-tier bleached wood pulp, so buyers specifying for premium white tissue or coated printing stock should confirm the target brightness threshold before ordering against this grade.<\/p>\n

\"B\u1ed9t<\/p>\n

C\u00e2u h\u1ecfi th\u01b0\u1eddng g\u1eb7p<\/h2>\n

Q: What’s the minimum tensile index for bleached bamboo pulp? <\/strong><\/h3>\n

A: >55 N\u00b7m\/g, tested to GB\/T 8940.2.<\/p>\n

Q: Is the viscosity range the same for every lot? <\/strong><\/h3>\n

A: Sheeon publishes 600\u2013800 ml\/g as the range for the product line, not a per-lot guarantee. Request the test report for the specific lot being shipped if viscosity is a hard requirement.<\/p>\n

Q: How does bleached bamboo pulp’s dirt count compare to unbleached bamboo pulp? <\/strong><\/h3>\n

A: Bleached grade runs tighter \u2014 <25 mm\u00b2\/500 g in the fine band versus <35 mm\u00b2\/500 g for unbleached \u2014 reflecting the additional cleaning that happens during bleaching.<\/p>\n

Q: Is bleached bamboo pulp priced differently from unbleached? <\/strong><\/h3>\n

A: Pricing depends on grade, specification, order volume, packaging and delivery terms, and is quoted per inquiry rather than published as a fixed rate.<\/p>\n

Buyers finalizing a spec sheet against this grade will get more predictive value from checking dirt count and viscosity on an incoming lot than from brightness alone \u2014 brightness is the number that’s easiest to verify visually, which is exactly why it’s also the easiest one for a supplier to overstate.<\/p>","protected":false},"excerpt":{"rendered":"

Bleached bamboo pulp runs approximately 85% brightness with viscosity in the 600\u2013800 ml\/g range, and those two numbers alone don’t tell you whether a lot will run cleanly on a tissue or printing line. This spec sheet breaks down every published parameter and what it actually predicts for each application.<\/p>","protected":false},"featured_media":1423,"comment_status":"closed","ping_status":"closed","template":"","class_list":["post-1422","news","type-news","status-publish","has-post-thumbnail","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/sheeonpulp.com\/vi\/wp-json\/wp\/v2\/news\/1422","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sheeonpulp.com\/vi\/wp-json\/wp\/v2\/news"}],"about":[{"href":"https:\/\/sheeonpulp.com\/vi\/wp-json\/wp\/v2\/types\/news"}],"replies":[{"embeddable":true,"href":"https:\/\/sheeonpulp.com\/vi\/wp-json\/wp\/v2\/comments?post=1422"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/sheeonpulp.com\/vi\/wp-json\/wp\/v2\/media\/1423"}],"wp:attachment":[{"href":"https:\/\/sheeonpulp.com\/vi\/wp-json\/wp\/v2\/media?parent=1422"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}